搜搜考试网英语翻译The length-to-diameter ratio of a bushing is important.A
来源：学生作业帮 编辑：搜搜考试网作业帮 分类：英语作业 时间：2024/07/07 10:39:45
英语翻译
The length-to-diameter ratio of a bushing is important.Allowable bering pressure per square inch of projected ared .The projected area is defined as the product of the length
of the bearing and the nominal inside diameter.Figure 7.3 shows the L- and D-dimensions
of asimple bearing of this type.The L/D ratio is seldom less than 1.If it is too small,lubrication becomes a real problem.If the ratio is greater than 4,there may be alignment problems and additional lubrication problems.In general,the most practical values for L/D ratio fall between 1 ½ and 2.Many "off-the-shelf" bushangs are available in this range.
The length-to-diameter ratio of a bushing is important.Allowable bering pressure per square inch of projected ared .The projected area is defined as the product of the length
of the bearing and the nominal inside diameter.Figure 7.3 shows the L- and D-dimensions
of asimple bearing of this type.The L/D ratio is seldom less than 1.If it is too small,lubrication becomes a real problem.If the ratio is greater than 4,there may be alignment problems and additional lubrication problems.In general,the most practical values for L/D ratio fall between 1 ½ and 2.Many "off-the-shelf" bushangs are available in this range.
The length-to-diameter ratio of a bushing is important.
轴衬的长-径比很重要.
Allowable bearing pressure per square inch of projected ared .
投影面积上每平方英寸容许承载压力
The projected area is defined as the product of the length of the bearing and the nominal inside diameter.
投影面积的定义为：轴承的长度和标称内径的乘积.
Figure 7. 3 shows the L- and D-dimensions of a simple bearing of this type.
图7.3为这类轴承的L（长度）和D（标称内径）尺寸规格
The L/D ratio is seldom less than 1.
L/D比值很少小于1
If it is too small,lubrication becomes a real problem.
如果该比值太小,润滑就成为实际问题.
If the ratio is greater than 4,there may be alignment problems and additional lubrication problems.
如果该比值大于4,就可能存在对中找正的问题,以及额外的润滑问题.
In general,the most practical values for L/D ratio fall between 1 ½ and 2.
总之,实际上最常见的L/D的比值处于1.5和2之间.
Many "off-the-shelf" bushings are available in this range.
许多轴衬的产品都符合这个范围.
轴衬的长-径比很重要.
Allowable bearing pressure per square inch of projected ared .
投影面积上每平方英寸容许承载压力
The projected area is defined as the product of the length of the bearing and the nominal inside diameter.
投影面积的定义为：轴承的长度和标称内径的乘积.
Figure 7. 3 shows the L- and D-dimensions of a simple bearing of this type.
图7.3为这类轴承的L（长度）和D（标称内径）尺寸规格
The L/D ratio is seldom less than 1.
L/D比值很少小于1
If it is too small,lubrication becomes a real problem.
如果该比值太小,润滑就成为实际问题.
If the ratio is greater than 4,there may be alignment problems and additional lubrication problems.
如果该比值大于4,就可能存在对中找正的问题,以及额外的润滑问题.
In general,the most practical values for L/D ratio fall between 1 ½ and 2.
总之,实际上最常见的L/D的比值处于1.5和2之间.
Many "off-the-shelf" bushings are available in this range.
许多轴衬的产品都符合这个范围.
英语翻译The ratio of one quantity to another is a fraction ,and
英语翻译IQ is the ratio of the age at which a child normally mak
英语翻译The thickness of the dome shell (measured as a ratio to
英文的数学题the ratio of blue marbles to green marbled in a bag is
The ratio of girls to boys in a class is 2:5.There are 8 gir
英语翻译Gross entry ratio.The total number of new entrants to a
英语翻译⒈the length of the perimeter of a right triangle is 60 i
A solar day is the length of time it takes the earth to revo
A solar day is the length of time ____ the earth to revolve
A solar day is the length of time ____ the earth to moce onc
a solar day is the length of time__the earth to go once arou
a solar day is the length of time____the Earth to revolve on